1Gas cooktopsInstallation instructionsand User guideNZ AUCG604 models
8 0– 2 0– 2Installation instructionsGas inlet pipeFastening the installation brackets (fig. 4)Each cooktop is provided with an installation kit inclu
9 Installation instructionsGas supply The connection must be executed by an authorised person according to the relevant standards. Bef
10Installation instructions1 After connecting the gas supply, check the piping and connections for leaks using a soap and water solution. The presenc
11 Installation instructionsConversion procedure (to convert to Universal LPG) replacing the injectors.Important! The conversion procedur
12Installation instructionsMinimum burner setting adjustment When changing from one type of gas to another, the minimum tap output must also be cor-re
13 Installation instructionsImportant! Installation must be carried out according to the manufacturer's instructions. Incorrect i
14Important! Replacing the power cord must be done by a qualified electrician in accordance with the instructions supplied by the manufacturer and in
15
16IntroductionAbout your new cooktopThank you for buying a Fisher & Paykel gas cooktop. Once it is installed and ready to use, you will want to kn
17Introduction1 Auxiliary burner2 Semi-rapid burner3 Rapid burner4 Wok burner5 Cooktop controlsFig.1 CG604 with rapid burner(no flame failure safety f
18Using your cooktopGas burnersThe knob (Fig. 3) controls the flow of gas through the safety tap. OFF = closed valve = maximum aperture or flow
19Lighting the cooktop1 Choose the control knob for the burner you want to use.2 Press the knob down gently and turn it anticlockwise to theposition.
20Using your cooktopFig.5 Cleaning the ignitor and probeIgnitorFlame failure probe(flame failure models only)If the cooktop does not lightIf the cookt
21Choosing a burnerUse flat-bottomed pans, and make sure that they match your burner, as shown in the following table. A small pot on a large burner
22Fig. 7 Incorrect use of wok on burnerWRONGFig. 8 Correct use of wok on wok stand over burnerCORRECTWok stand - models fitted with wok burner only (f
23General adviceMaintenance Period DescriptionDaily Clean gas cooktop as per following instructions.Monthly Remove all burner parts, and clean using a
24Burners and pan supports You can remove and clean these parts with hot soapy water or other appropriate products - see ‘Cleaning chart’. After clean
25Replacing the wok burner To replace the wok burner:1 Fit the burner ring to the housing as shown by the arrow in fig. 11. Make sure the burner is n
26Care and cleaningCleaning chartCooktop part Cleaning ImportantTrivets/pan supports, burner caps Hot soapy water and nylon scourer. Soap removeable p
27TroubleshootingTroubleshooting chartProblem Possible solutionsMy cooktop does not light Check the cooktop is plugged in and the electricity is switc
1ContentsSafety and warnings 2 Installation instructions 6Introduction 16Using your cooktop 18Care and cleaning 23Troubleshooting 27Warranty
28Warranty and serviceBefore you call for service or assistance ...Check the things you can do yourself. Refer to the installation instructions and y
30Copyright © Fisher & Paykel 2007. All rights reserved.The product specifications in this booklet apply to the specific products and models descr
2Important safety precautions Installation Read these instructions carefully before installing or using this product. Please make this information av
3 Particular attention shall be given to the relevant requirements regarding ventilation. This product should not be sealed into the bench with silico
4Safety and warnings WARNING!Hot Surface HazardThis appliance becomes hot during use.Do not touch the cooktop components, burners, trivets/pan support
5 Important safety precautionsOperation Children, or persons with a disability which limits their ability to use the appliance, should have a respon
65804805006034 0–2560200 0–2The installation shall comply with the dimensions in Figures 1 and 2, bearing in mind that: A minimum clearance of 20 m
7 Installation instructions20 mm750 mm60 mm min200 mm min500 mm450 mmFig. 2Fig. 3Clearances Installation clearances and protection of co
Comments to this Manuals