Fisher Paykel DD24SCHTX9N Installation Guide

Double DishDrawerTM dishwasherDD24DA & DD24DCT modelsUS CAINSTALLATION INSTRUCTIONS591153A 07.16www.fi sherpaykel.com

98 RECOMMENDED METHOD (A) - SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY ONLY)NOW CHOOSE WHICH INSTALLATION METHOD (A) OR (B) IS MORE SUITABLE F

10!1-A SECURE TO THE CABINETRY ON THE SIDES !2-A OPTIONALLY SECURE TO THE CABINETRY ABOVE213Open the drawer halfway.Using a flat bladedscrewdriver

118 ALTERNATIVE METHOD (B) - SECURE BY DRAWER REMOVAL(x2)As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twiste

121234!1-B SECURE TO THE CABINETRY ON THE SIDES !2-B OPTIONALLY SECURE TO THE CABINETRY ABOVEx4Secure using two pairsof formed brackets(use 5⁄8” (

13!4-B FIT THE SUPPLIED TOEKICK PANEL1913578926419IMPORTANT!Do not overtighten screw.Where the toekick meets the bottom of the tub is the cut-off poin

1412!5 THERE ARE THREE DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE.DRAINAGE OPTION 1Dishwasher and Ø 1 1/2” (38 mm) Standpi

15min. R 8” (200 mm)IMPORTANT!Ensure that drain connection will comply with local plumbing regulations.DRAINAGE OPTION 2Dishwasher using Air Break wit

16123min. R 8” (200 mm)IMPORTANT!Ensure that drain connection will comply with local plumbing regulations.DRAINAGE OPTION 3Dishwasher using drain hose

17Ensure the supplied rubber washer is fitted inside the coupling.Tighten coupling with spanner.180oNo leaks!12!8 TROUBLESHOOTING ●Excessive water rem

18!9 FINAL CHECKLISTTO BE COMPLETED BY THE INSTALLERComplete and keep for safe reference:Model Serial No. Purchase Date Purchaser Dealer Address I

1IMPORTANT! SAVE THESE INSTRUCTIONSThe models shown in this installation guide may not be available in all markets and are subject to change at any

Single DishDrawerTM dishwasherDD24SA & DD24SCT modelsUS CAINSTALLATION INSTRUCTIONS591153A 07.16www.fi sherpaykel.com

1IMPORTANT! SAVE THESE INSTRUCTIONSThe models shown in this installation guide may not be available in all markets and are subject to change at any

22 PARTS SUPPLIEDIf the Drain hoses supplied are not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which wi

32133 OPTIONALLY HARD WIRING PRIOR TO INSTALLATION3-A REMOVE THE DRAWER 3-B REMOVE THE ACCESS COVER & REMOVE POWER Access coverClipClipElect

43 OPTIONALLY HARD WIRING PRIOR TO INSTALLATIONIMPORTANT!Ensure the mains wires are routed UNDERNEATH all other harness wiring from the electronics

54 PRODUCT DIMENSIONSDD24SA DD24SCTPRODUCT DIMENSIONS INCHES (MM) INCHES (MM)AOverall height of product116 1/8” (410) 17 7/8” (454)BOverall widt

65 CABINETRY DIMENSIONSDD24SA DD24SCTCABINETRY DIMENSIONS INCHES (MM) INCHES (MM)KInside height of cavity min. 16 1/4” (412) min. 18” (456)LInsi

76 CAVITY PREPARATIONWater ConnectionRecommended HOT (Maximum 140°F/60°C).Supplied hose to suit 3/8” (9 mm) male Water Pressure Water softener modelsM

22 PARTS SUPPLIEDIf the Drain hoses supplied are not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which wi

87 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGELEFT HAND SIDE RIGHT HAND SIDEDrain hose - 78 1/2” (2000 mm) Drain hose - 70 1/2” (1800 mm)In

98 RECOMMENDED METHOD (A) - SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY ONLY)NOW CHOOSE WHICH INSTALLATION METHOD (A) OR (B) IS MORE SUITABLE F

10213!1-A SECURE TO THE CABINETRY ON THE SIDESOpen the drawer halfway.Using a flat bladedscrewdriver, prise the grey rubber plug out of the trim mould

118 ALTERNATIVE METHOD (B) - SECURE BY DRAWER REMOVAL9-B PULL THROUGH HOSES & PUSH INTO THE CAVITY !0-B REMOVE THE LOWER DRAWERAs you push product

12121234!2-B REFIT THE DRAWER ONTO THE RUNNERS!1-B SECURE TO THE CABINETRY ON THE SIDESBefore refitting the drawer, ensure the hoses are not twisted a

1312!3 THERE ARE THREE DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE.DRAINAGE OPTION 1Dishwasher and Ø 1 1/2” (38 mm) Standpi

1412min. R 8” (200mm)IMPORTANT!Ensure that drain connection will comply with local plumbing regulations.DRAINAGE OPTION 2Dishwasher using Air Break wi

15312min. R 8” (200mm)IMPORTANT!Ensure that drain connection will comply with local plumbing regulations.DRAINAGE OPTION 3Dishwasher using drain hose

16Ensure the supplied rubber washer is fitted inside the coupling.Tighten coupling with spanner.180oNo leaks!12!4 CONNECT INLET HOSE TO HOT WATER !5

17!6 TROUBLESHOOTING ●Excessive water remaining above the filter plate, after the rinse cycle. (This is displayed as an A3 fault)Check for a kinked dr

33 OPTIONALLY HARD WIRING PRIOR TO INSTALLATION3-A REMOVE THE LOWER DRAWER 3-B REMOVE THE ACCESS COVER & REMOVE POWER Access coverClipClipEl

18!7 FINAL CHECKLISTTO BE COMPLETED BY THE INSTALLERComplete and keep for safe reference:Model Serial No. Purchase Date Purchaser Dealer Address I

43 OPTIONALLY HARD WIRING PRIOR TO INSTALLATIONIMPORTANT!Ensure the mains wires are routed UNDERNEATH all other harness wiring from the electronics

54 PRODUCT DIMENSIONSDD24DA DD24DCTPRODUCT DIMENSIONS INCHES (MM) INCHES (MM)AOverall height of product132 5/16 - 34 5/8” (820-880)234 - 36 3/8”

65 CABINETRY DIMENSIONSMinimum clearances from adjacent cabinetrymin. 1/2” (13 mm)clearance from a corner cupboardBracket slotsmin. 1/16” (2 mm)clea

76 CAVITY PREPARATIONWater ConnectionRecommended HOT(Maximum 140°F/60°C).Supplied hose tosuit 3⁄8” (9 mm) malecompression fitting.Kosher requirementsD

8LEFT HAND SIDE RIGHT HAND SIDE7 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGEDrain hoses - 78 1/2” (2000 mm)Drain hoses - 70 1/2” (1800 mm)I