Fisher & Paykel DD605 User Manual

599464 Diagnostic Manual DishDrawer™ MODELS: DD605 DS605 Fisher & Paykel Appliances © 2007 - All Rights Reserved

599464 10As mentioned on the previous page, the LCD display and touch switch panel LEDs are illuminated to correspond to a particular hardware device

599464 11 3.6 Fast Test Cycle WARNING: Only run this cycle if the DishDrawer™ is connected to the water supply. This level runs an 8 minute fast test

599464 12The test sequence in fast cycle mode performs 33 tests. The number of any failed test is displayed on the touch switch panel LEDs. The test

599464 13 3.8 Temperature & Voltage Display Mode (Not available on integrated or flat door models) During a wash cycle, the current water temperat

599464 14The DishDrawer™ is still in the Showroom wash mode however, and it can be re-run by pressing POWER and then START/PAUSE. Once show off/show

599464 15 4.2 Hardware Output Test Mode Press and hold KEYLOCK, then START/PAUSE for 5 seconds. All LEDs & LCD segments except Keylock are illumin

599464 164.3 Fast Test Cycle Press and hold KEYLOCK, then START/PAUSE for 5 seconds. All LEDs & LCD segments except Keylock are illuminated. Pres

599464 17 4.6 Fault Codes There are 10 F (fatal) faults, which are displayed in the LCD along with the symbol of a spanner (not on integrated or flat

599464 18Once the fault has been cleared for an F3, F8 or F9 fault, the power needs to be disconnected and reconnected to reset the isolation relay b

599464 19 Fault Code LED Display Fault Possible Causes F2 Delicate LED. The controller has not sensed the motor rotating. • Foreign object has jamm

599464 - September 2007 CONTENTS 1 DIMENSIONS & SPECIFICATIONS...3 1.1 Product Size (mm)...

599464 20Fault Code LED Display Fault Possible Causes F7 Fast, Delicate and Rinse LEDs. No lid motor current detected. • Lid actuator not connected

599464 21 Fault Code LED Display Fault Possible Causes U1 Heavy and Rinse LED. Machine has failed to prime with water within approx. 3 minutes. • T

599464 224.8 Fault Code Problem Solving Charts The following charts can be used as a guide to help locate faults in a DishDrawer™. F1 Flood Detected

599464 23 F2 Motor Not Rotating The controller has not sensed the motor rotating. The product will pause the wash program, log the fault, and report

599464 24F3 Water Temperature Measurement Exceeds 85 Degrees Celsius The water temperature is sensed at greater than 85 degrees C / 185 degrees F. T

599464 25 F4 Element Has Been On Too Long (About 4 Hours) And Water Has Not Reached Required Temperature The element has been on too long (about 3 ho

599464 26F6 Lid Motors Ran But Did Not Reach Stall Current Lid actuators ran but did not reach stall current. The product will pause the wash progra

599464 27 F8 Earth Leakage Fault Earth leakage fault. The product will disable the power supply, log the fault, lock out the user and report to the us

599464 28F9 Power Supply/Controller Fault Power supply/controller fault. The product will disable power supply, log the fault, lock out the user and

599464 29 FF Top Tub Not Responding Top tub not responding. PRIMARY ACTION - Check the top controller works when swapped with the bottom controller

599464 3 1 DIMENSIONS & SPECIFICATIONS 1.1 Product Size (mm) Height (double) 819.5 – 879.5mm Height (single) 409mm Width 595mm Depth 570mm

599464 30U2 Restricted Lid Travel Restricted lid travel. The lid has reached its stall current too soon. The product will retry the lid 3 times, lo

599464 31 U4 This Fault is Advisory Only. The Other Tub has a Fault and has Disabled the Power Supply. This fault is advisory only. The other tub h

599464 324.8.1 Poor Dry Performance Poor Dry Performance Question Yes No 1 Is the customer complaining of plastic items not drying? Advise custom

599464 33 4.8.2 Poor Wash Performance Customers Complaint Food Particles left on Dishes Cause of problem (1) Spray arm has stopped rotating. How to

599464 34Customers Complaint Dishes have blotchy marks on them that look like water stain marks not food Cause of problem. Not enough rinse aid being

599464 35 Where a water softener is fitted; Set the water softener for the correct local water supply hardness. Check that the water softener is func

599464 36To check that the amount spray leakage is appropriate:- Fill the salt reservoir with water. • In diagnostics mode, turn on the fill water

599464 37

599464 385 WIRING DIAGRAM 5.1 Power Distribution Concept Heater PlateIsolationrelayAuxillary PSUMainsmain PSUOutput Driversdispenser, water soft

599464 39 5.2 Wiring Diagram

599464 4Drain Hose 2.01m (78 inches) from rear of cabinet 2.5m (98 inches) bottom tub 2.9m (114 inches) top tub Detergent Dispenser 24 Volt D

599464 5 2 OPTION ADJUSTMENT 2.1 Changing Setup Options To enter the option adjustment mode, press POWER to turn the LCD on, then hold the ECO butto

599464 6Press KEYLOCK to advance the rinse aid setting. Once the desired setting is achieved, press POWER to exit. The rinse aid index is stored in

599464 7 2.1.5 Closed Drawer Option (Ld) The closed drawer option can be turned on or off using the KEYLOCK button. If the scrubbing brush symbol is

599464 83 DIAGNOSTICS 3.1 DishDrawer™ Diagnostics Dishwasher Diagnostics can only be entered in Power Off mode, i.e. when there is no display on th

599464 9 3.5 Hardware Output Diagnostic Test Mode This level tests all the hardware outputs and inputs. The LCD display shows “HO”. Press POWER to