Fisher Paykel DD24STI9N Installation Guide

59186 A 08.17INSTALLATION GUIDEUS CADD24DI, DD24DTI & DD24DHTI modelsDOUBLE DISHDRAWERTM DISHWASHER

98 CAVITY PREPARATIONWater ConnectionRecommended HOT(Maximum 140°F/60°C).Supplied hose tosuit 3⁄8” (9 mm) malecompression fitting.Kosher requirementsD

109 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGELEFT HAND SIDE RIGHT HAND SIDEDrain hoses - 78 1/2” (2000mm)Drain hoses - 70 1/2” (1800mm)In

11(x2)!0 RECOMMENDED METHOD (A) - SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY ONLY)NOW CHOOSE WHICH INSTALLATION METHOD (A) OR (B) IS MORE SUIT

12213(x2)!2-A SECURE TO THE CABINETRY ON THE SIDES!4-A AFTER SECURING, REFER TO ‘FIT THE SUPPLIED TOEKICK PANEL’ STEP!3-A OPTIONALLY SECURE TO T

13(x2)!0 ALTERNATIVE METHOD (B) - SECURE BY DRAWER REMOVALAs you push product in, pull through hoses and cord, ensuring they don’t get kinked or twist

14x4(x2)!2-B SECURE TO THE CABINETRY ON THE SIDES !3-B OPTIONALLY SECURE TO THE CABINETRY ABOVESecure using two pairs of formed brackets. Repeat o

15!5 INSTALLING CUSTOM FRONT DRAWER PANELS112Electrical Shock HazardWARNING!Before continuing, ensure that the product is disconnected from the power

16!5 INSTALLING CUSTOM FRONT DRAWER PANELS2325/8” (16mm)(x6)41125/8” (16mm) (x3)!5-C ATTACH CUSTOM PANELS TO PANEL BRACKETSThere must be at least3 s

17!5 INSTALLING CUSTOM FRONT DRAWER PANELS!5-E CONNECT THE KNOCK-TO-PAUSE MODULE TO THE CONTROLLER!5-G ATTACH CUSTOM PANELS TO PRODUCT!5-F RECONN

18!6 FITTING A CUSTOM TOEKICK PANELPROFILE APROFILE B9Custom Toekick PanelToekick mounting bracket cutting templateCustom toekick panelToekick mountin

11 SAFETY AND WARNINGS WARNING!Electrical Shock HazardWARNING: To reduce the risk of electrical shock, fire, or injury to persons, the installer mus

19!6 FIT THE SUPPLIED PREFINISHED TOEKICK PANEL (IF PREFERRED)1234191956897IMPORTANT!Do not overtighten screw.Slide the toekick onto the mounting rail

2012!7 THERE ARE THREE DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE.DRAINAGE OPTION 1Dishwasher and Ø 1 1/2” (38 mm) Standpi

21min. R 8” (200 mm)IMPORTANT!Ensure that drain connection will comply with local plumbing regulations.DRAINAGE OPTION 2Dishwasher using Air Break wit

22123min. R 8” (200 mm)IMPORTANT!Ensure that drain connection will comply with local plumbing regulations.DRAINAGE OPTION 3Dishwasher using drain hose

23Ensure the supplied rubber washer is fitted inside the coupling.Tighten coupling with spanner.180oNo leaks!12@0 TROUBLESHOOTING ●Excessive water rem

24@1 FINAL CHECKLISTTO BE COMPLETED BY THE INSTALLERComplete and keep for safe reference:Model Serial No. Purchase Date Purchaser Dealer Address I

59186 A 08.17INSTALLATION GUIDEUS CADD24SI, DD24STI & DD24SHTI modelsSINGLE DISHDRAWERTM DISHWASHER

11 SAFETY AND WARNINGS WARNING!Electrical Shock HazardWARNING: To reduce the risk of electrical shock, fire, or injury to persons, the installer mus

22 PARTS SUPPLIEDClamp (1)(for securing Drain hose joiner)Wire clip (1) (for securing Drain hose joiner)Phillips 16 mm screws (7)38 mmbottom fixing

33 OPTIONALLY HARD WIRING PRIOR TO INSTALLATION3-A REMOVE THE DRAWER 3-B REMOVE THE ACCESS COVER & REMOVE POWER Access coverClipClipElectron

22 PARTS SUPPLIEDIf the Drain hoses supplied are not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which wi

43 OPTIONALLY HARD WIRING PRIOR TO INSTALLATIONIMPORTANT!Ensure the mains wires are routed UNDERNEATH all other harness wiring from the electronics

54 PRODUCT DIMENSIONSDD24SIDD24STIDD24SHTIPRODUCT DIMENSIONS INCHES (MM) INCHES (MM)AOverall height of product 116 1/8” (410) min. 17 7/8” (454)

65 CABINETRY DIMENSIONSDD24SIDD24STIDD24SHTICABINETRY DIMENSIONS INCHES (MM) INCHES (MM)JInside height of cavitymin. 16 1/4” (412) min. 18” (4

76 CUSTOM DRAWER PANEL SPECIFICATIONSThe following calculations assume the top of the upper panel is aligned with the top of the adjacent cabinetry.

87 CAVITY PREPARATIONWater ConnectionRecommended HOT (Maximum 140°F/60°C).Supplied hose to suit 3/8” (9 mm) male Water Pressure Water softener modelsM

9ø 2 3⁄8” (60mm)ø 2 3⁄8” (60mm)ø 2 3⁄8” (60mm)ø max. 1 1⁄2” (38mm)ø max. 1 1⁄2” (38mm)ø 2 3⁄8” (60mm)max. 3⁄16” (5mm)max. 3⁄16” (5mm)8 11⁄16” (220mm)8

109 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE!0 TALL HEIGHT INTEGRATED MODELS FOR 18 7⁄8” (480MM) CAVITY ONLY - ATTACH CAVITY BRACKETLEFT

11!1 RECOMMENDED METHOD (A) - SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY ONLY)NOW CHOOSE WHICH INSTALLATION METHOD (A) OR (B) IS MORE SUITABLE

12As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted. IMPORTANT!If product cannot be pushed in far enough,

13!1 ALTERNATIVE METHOD (B) - SECURE BY DRAWER REMOVAL!1-A ATTACH VENTING HOSEFitted ElbowCheck that the fitted elbow is rotated left or right (depe

33 OPTIONALLY HARD WIRING PRIOR TO INSTALLATION3-A REMOVE THE LOWER DRAWER 3-B REMOVE THE ACCESS COVER & REMOVE POWER Access coverClipClipEl

1421344!3-B REMOVE THE DRAWER !4-B SECURE TO THE CABINETRY ON THE SIDES4” (100mm)To prevent kinked hosesEither sit the drawer down on the left han

1512344” (100mm)!5-B REFIT THE DRAWER ONTO THE RUNNERS!6-B SECURE THE EXTERNAL VENTBefore refitting the drawer, ensure the hoses are not twisted a

16!7 INSTALLING A CUSTOM FRONT DRAWER PANEL112Electrical Shock HazardWARNING!Before continuing, ensure that the product is disconnected from the power

172316mm (x6)!7 INSTALLING CUSTOM FRONT DRAWER PANELS1216mm (x3)!7-C ATTACH CUSTOM PANELS TO PANEL BRACKETSThere must be at least3 screws used each

18!7 INSTALLING CUSTOM FRONT DRAWER PANELS!7-E CONNECT THE KNOCK-TO-PAUSE MODULE TO THE CONTROLLER!7-G ATTACH CUSTOM PANEL TO PRODUCT!7-F RECONN

1912!8 THERE ARE THREE DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE.DRAINAGE OPTION 1Dishwasher and Ø 1 1/2” (38 mm) Standpi

2012min. R 8” (200mm)IMPORTANT!Ensure that drain connection will comply with local plumbing regulations.DRAINAGE OPTION 2Dishwasher using Air Break wi

21312min. R 8” (200mm)IMPORTANT!Ensure that drain connection will comply with local plumbing regulations.DRAINAGE OPTION 3Dishwasher using drain hose

22Ensure the supplied rubber washer is fitted inside the coupling.Tighten coupling with spanner.180oNo leaks!12!9 CONNECT INLET HOSE TO HOT WATER @0

23@1 TROUBLESHOOTING ●Excessive water remaining above the filter plate, after the rinse cycle. (This is displayed as an A3 fault. See user guide ‘How

43 OPTIONALLY HARD WIRING PRIOR TO INSTALLATIONIMPORTANT!Ensure the mains wires are routed UNDERNEATH all other harness wiring from the electronics

24@2 FINAL CHECKLISTTO BE COMPLETED BY THE INSTALLERComplete and keep for safe reference:Model Serial No. Purchase Date Purchaser Dealer Address I

25

26

54 PRODUCT DIMENSIONSSTANDARDHEIGHTMODELSTALLHEIGHTMODELSPLANPROFILEFRONTDD24DIDD24DTIDD24DHTIPRODUCT DIMENSIONS INCHES (MM) INCHES (MM)AOverall

65 CABINETRY DIMENSIONSMinimum clearances from adjacent cabinetrySTANDARDHEIGHTMODELSTALLHEIGHTMODELSDD24DIDD24DTIDD24DHTICABINETRY DIMENSIONS INC

76 CUSTOM DRAWER PANEL SPECIFICATIONSThe following calculations assume the top of the upper panel is aligned with the top of the adjacent cabinetry.

87 CUSTOM TOEKICK PANEL SPECIFICATIONSHEIGHT OF THE TOEKICK PANELMeasure D (height from the top of adjacent cabinet door fronts to the floor) and wr