Fisher Paykel RS36A80J1N User Manual

ActiveSmart™ Built-in refrigeratorRS36A80J and RS36A80U modelsUS CAINSTALLATION INSTRUCTIONS843155 B 08.15www.fisherpaykel.comFramed cabinetry

85 PRODUCT AND CAVITY DIMENSIONSPRODUCT DIMENSIONSinches (mm)DOverall height of product* 79⁄” (2028)EOverall width of product 35⅓” (890)FMini

95 PRODUCT AND CAVITY DIMENSIONSDOOR CLEARANCE DIMENSIONS inches (mm)ADepth of door (widest opening) measured from front of cabinetry 18⁄” (480

105 PRODUCT AND CAVITY DIMENSIONS – WITH RD3680 DOOR PANEL SETRS36A80J model shown with RD3680 door panels.CAVITY DIMENSIONS inches (mm)AOverall hei

115 PRODUCT AND CAVITY DIMENSIONS – WITH RD3684 DOOR PANEL SETRS36A80J model shown with RD3684 door panels.CAVITY DIMENSIONS inches (mm)AOverall hei

125 PRODUCT AND CAVITY DIMENSIONS – WITH RD3680/RD3684 DOOR PANEL SETDOOR CLEARANCE DIMENSIONS inches (mm)ADepth of door (widest opening) measured f

13ACB6 CAVITY PREPARATIONSElectricalPlumbingElectricalPlumbingAlternative area above cavity for electrical connectionsMINIMUM CAVITY DIMENSIONS inch

147 CUSTOM DOOR PANEL DIMENSIONSHDABDgAEIFCgRS36A80JDIMENSIONS inches (mm)AHeight of top door panel min.45⁄–max.49⁄” (min. 1150–max.

157 CUSTOM DOOR PANEL DIMENSIONSThe drawings below apply to non-Water dispensing models only (RS36A80J). Dimensions are shown in Imperial (inches) a

168 80” (2032 mm) CAVITY – ATTACH ANTI-TIP BRACKETIMPORTANT!Safety requires refrigerators be stable when doors and/or drawer, are open. The anti-tip

178 84” (2134 mm) CAVITY – ATTACH ANTI-TIP BRACKETIMPORTANT!Safety requires refrigerators be stable when doors and/or drawer, are open. The anti-tip

18WARNING!Take care when working with the appliance outside of the finished enclosure, as the appliance is not secured and has the possibility of tipp

19WARNING!Take care when working with the appliance outside of the finished enclosure, as the appliance is not secured and has the possibility of tipp

20!0 CONNECT TO WATER AND ELECTRICAL SUPPLYIMPORTANT!The water connection instructions below are intended only for the professional installer.DO

215 Thread the free end of the water hose into the dedicated hole located in the base of the appliance, through to the back of the appliance (refer t

22!1 PRE-ALIGNING YOUR PRODUCTIMPORTANT!It is important that the doors are in line with the frame and the appliance is centred before following th

23!2 INSTALL WATER FILTER CARTRIDGE AND KICKSTRIPS2 Pull the freezer drawer out slightly and insert the filter cartridge and tool into the bottom l

24!3 ASSEMBLE DOOR PANEL SETThe assembly of Fisher & Paykel kits (EZKleen stainless steel door panels) and custom door panels are outlined below

25!4 HANGING ICE & WATER DOOR PANEL2 Angle top display tabs into the door panel. Ensure the harness is free of pinching. Firmly push against bo

26!5 HANGING NON-WATER DISPENSING DOOR PANELS2 Lock top inner panel side screws to allow opening the doors without affecting adjustment. (Open the

27!6 ICE AND WATER INITIATIONIce maker initiationTo initiate ice maker before use:When the appliance is first turned on after installation, the ic

1FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR CABINETRYRS36A80J and RS36A80U modelsFRAMELESS CABINETRY(Frameless: Aligns the product with the cab

28!7 ATTACH FIXING BRACKETS1 Carefully open the refrigerator French doors to attach fixing brackets. Place fixing bracket over the side of the appl

29!8 ATTACH COVERS AND TOE KICK1 Remove any remaining protective film on your door panels.2 Open the refrigerator French doors, firmly push top co

30!9 ATTACH BOTTOM KICKSTRIPFor toe kick installation higher than 4” (102 mm)1 Measure the required height for the bottom grille. On a board, caref

31@0 ATTACH SIDE TRIM BRACKETSIMPORTANT!Before installing your appliance, ensure the dimensions of the finished enclosure are correct for your appli

32@1 ATTACH SIDE TRIMSAPlasticAluminumFor 80” (2032 mm) and 84” (2134mm) cavity installations1 Place the side trim against the alcove side wall wi

33@2 ADJUSTING HINGE TENSIONING SCREWSHinge tensioning screwAHinge tensioning screws can be tightened if increased door closing force is required.1

34@3 FINAL CHECKLISTComplete and keep for safe reference:Model Serial No.Purchase Date PurchaserDealer Address Installer’s NameInstaller’s Signatur

843155 B 08.15www.fisherpaykel.comCopyright © Fisher & Paykel 2015. All rights reserved.The product specifications in this booklet apply to the s

31 SAFETY AND WARNINGS! WARNING!Electric Shock HazardRead and follow the safety and warnings outlined in this installation instructions guide before

43 COMPONENTS LISTFrench door hanging bracket(2)Drawer hanging bracket(1)Side bracket(10)Side strap(10)M5x10 pan head Phillips screw (10)Door pa

53 COMPONENTS LISTDoor handle(3)Optional accessories – The standard appliance does not include a door panel set.Fisher & Paykel door panel sets

63 COMPONENTS LISTTop kickstrip grille(1)Kickstrip filter(1)Air divider(1)Product hardware – Included with standard appliance.Screw cover(4) Bottom

74 MAXIMUM DISTANCE OF HOSE AND POWER CORDPower cord (excl. plug) – 80 ¾” (2051mm)RIGHT HAND SIDEPower cord (excl. plug) – 80 ¾” (2051mm)LEFT HAND