ActiveSmart™ Integrated Door Drawer RefrigeratorRS36W80 modelsUS CAINSTALLATION INSTRUCTIONS844189 A 04.16www.fisherpaykel.comwww.dcsappliances.co
85 PRODUCT AND CAVITY DIMENSIONSPRODUCT DIMENSIONSinches (mm)DOverall height of product* (does not include front panels) 79 7/8” (2028)EOverall widt
95 PRODUCT AND CAVITY DIMENSIONSDOOR OPENING AND CLEARANCE DIMENSIONS inches (mm)ADepth of door (widest opening) measured from front of door 37” (9
105 PRODUCT AND CAVITY DIMENSIONS – WITH RD3680 OR RD3680C DOOR PANEL SETRS36W80RJ or RS36W80RJC models shown with RD3680 or RD3680RC door panels.CA
115 PRODUCT AND CAVITY DIMENSIONS – WITH RD3684 AND RD3684C DOOR PANEL SETRS36W80RJ or RS36W80RJC models shown with RD3684R or RD3684RC door panels.
125 PRODUCT AND CAVITY DIMENSIONS – WITH RD3680/RD3684 DOOR PANEL SET12RS36W80RUC RS36W80(R/L)JCRS36W80RU RS36W80(R/L)JDOOR OPENING AND CLEARANCE DI
13ACB6 CAVITY PREPARATIONSCAVITY DIMENSIONS inches (mm)AOverall height of cavity 80/84” (2032/2134)BOverall width of cavity 36” (914)COverall depth
147 CUSTOM DOOR PANEL DIMENSIONSRS36W80J RS36W80JC CUSTOM PANEL DIMENSIONS inches (mm)AHeight of top door panel 45 5/16–49 5/16” (1150–1252)BWi
157 CUSTOM DOOR PANEL DIMENSIONSThe drawings below apply to non-Water dispensing models only (RS36W80(R/L)J/RS36W80(R/L)JC). Dimensions apply for th
168 80” (2032mm) CAVITY – ATTACH ANTI-TIP BRACKETIMPORTANT!Safety requires refrigerators be stable when door and/or drawer, are open. The anti-tip b
178 84” (2134mm) CAVITY – ATTACH ANTI-TIP BRACKETIMPORTANT!Safety requires refrigerators be stable when door and/or drawer, are open. The anti-tip b
188 84” (2134mm) CAVITY – ATTACH TOP TRIMWARNING!Take care when working with the appliance outside of the finished enclosure, as the appliance is no
19WARNING!Take care when working with the appliance outside of the finished enclosure, as the appliance is not secured and has the possibility of tipp
20!0 CONNECT TO WATER AND ELECTRICAL SUPPLYIMPORTANT!The water connection instructions below are intended only for the professional installer.DO
215 Thread the free end of the water line hose into the dedicated hole located in the base of the appliance, through to the back of the appliance (re
22IMPORTANT!It is important that all four corners of the appliance are supported firmly onto the floor to eliminate any movement.Installing the ap
23!2 INSTALL WATER FILTER CARTRIDGE AND KICKSTRIPS2 Pull the freezer drawer out slightly and insert the filter cartridge and tool into the bottom le
24!3 ASSEMBLE DOOR PANEL SETThe assembly of Fisher & Paykel (EZKleen stainless steel) and DCS (Stainless steel) door panels and custom door pane
25!4 HANG ICE & WATER DOOR PANEL2 Angle top display tabs into the door panel. Ensure the harness is free of pinching. Firmly push against botto
26!5 HANG NON-WATER DISPENSING DOOR PANELS6 Once satisfied with all door panels, secure M8 studs with M8 washer and M8 nut (refer to B). The top of
27!6 ICE AND WATER INITIATIONIce maker initiationTo initiate ice maker before use:When the appliance is first turned on after installation, the ic
1FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR CABINETRYFISHER & PAYKEL: RS36W80(R/L)J and RS36W80RU modelsDCS: RS36W80(R/L)JC and RS36W80RUC
28!7 ATTACH FIXING BRACKETS1 Carefully open the refrigerator door to attach fixing brackets. Place fixing bracket over the side of the appliance an
291 If applicable, remove any remaining protective film on your door panels.2 Open the refrigerator door, firmly push top cover over the top studs.R
30!9 ATTACH BOTTOM GRILLESFor custom toe tick greater than 4” (102mm)1 Measure the required height for the bottom grille. On a board, carefully sco
31APlasticAluminumFor 80” (2032 mm) cavity installation only2 Measure 4” (102mm) from the top, shorter side trim and carefully cut using a fine tooth
32@0 ATTACH SIDE TRIM BRACKETS – (A) FLEXIBLE SPRING CLIP METHOD4 Insert the spring clip into the gap between the side trim and side trim bracket,
33@0 ATTACH SIDE TRIM BRACKETS – (B) FIXED SCREW METHOD3 Position three side trim brackets on each side (refer to B for bracket locations). Open t
344 Place the side trim against the alcove side wall with the shorter lip facing the bottom (refer to D).Ensure the side trim is positioned as high
35@1 ADJUST HINGE TENSIONING SCREWSHinge tensioning screws can be tightened if increased door closing force is required.1 To ensure the door shuts
36@2 FINAL CHECKLISTComplete and keep for safe reference:Model Serial No.Purchase Date PurchaserDealer Address Installer’s NameInstaller’s Signatur
844189 A 04.16www.fisherpaykel.comwww.dcsappliances.com© Fisher & Paykel Appliances 2016. All rights reserved.The product specifications in th
31 SAFETY AND WARNINGS! WARNING!Electric Shock Hazard Read and follow the safety and warnings outlined in this installation instructions guide befor
43 COMPONENTS LISTDoor hanging bracket(1)Drawer hanging bracket(1)Side bracket(6)Side strap(6)M5x10 pan head Phillips screw (6)Door panel fitting
53 COMPONENTS LISTOptional accessories – The standard appliance does not include a door panel set.Fisher & Paykel (EZKleen stainless steel) and
63 COMPONENTS LISTProduct hardware – Included with standard appliance.Air divider(1)Screw cover(4) Top trim joining bracket*(2)Spring Clip (6)(for S
74 MAXIMUM DISTANCE OF HOSE AND POWER CORDPower cord (excl. plug) – 80 3/4” (2051mm)RIGHT HAND SIDEPower cord (excl. plug) – 80 3/4” (2051mm)LEFT HA
Comments to this Manuals